Domestic Robot

Home / Robot vacuums / Troubleshooting

Robot vacuums · Researched, not tested

Robot vacuum troubleshooting: common problems and fixes

Most robot vacuum faults have a simple cause. Here's what to check first when your robot won't charge, gets stuck, loses suction or drops off Wi-Fi, and when to stop and make a warranty claim.

By Domestic Robot · Editor: Christian Ganaban · Updated 21 November 2026 · We may earn a commission from links on this page. Disclosure

Researched, not testedThis guide is general advice drawn from manufacturer manuals, support pages and our existing research. We haven't diagnosed or repaired these robots ourselves.

Quick answer

Most robot vacuum problems come down to four things: dirty sensors or charging contacts, a full bin or dock bag, hair wrapped around the brushes, and Wi-Fi settings. Clean those first, restart the robot and dock, and update the app. If the fault keeps coming back, check the error code on the brand's support page and contact the seller or brand about a warranty claim before you open anything up. Your rights under the Australian Consumer Law apply on top of the brand warranty.

Common problems and first fixes

ProblemCommon causesFirst things to try
Won't charge or dockDirty charging contacts, dock moved or blocked, power point switched offWipe the contacts on the robot and dock with a dry cloth, give the dock clear space either side, check the power point
Stops mid-clean or says it's stuckCords, rug tassels, low furniture, door thresholdsTidy cords, set no-go zones in the app around problem spots, check the brand's listed threshold height
Poor suction or leaves dirt behindFull bin or dock bag, clogged filter, hair wrapped on the brushEmpty the bin, replace the dock bag, clean or replace the filter, cut hair off the main brush
Main brush or side brush not spinningHair and thread wound around the brush endsRemove the brush, clear the ends and bearings, refit; replace worn brushes
Mop leaves streaks or smellsDirty mop pads, old water in the dock, too much water flowWash or replace pads, empty and rinse the dirty-water tank, lower the water setting in the app
Map lost or rooms wrongFurniture moved, lighting changed, sensor windows dirtyWipe the LiDAR or camera window, re-run mapping, then re-draw room dividers
Won't connect to Wi-FiRouter on 5GHz only, weak signal at the dock, app or firmware out of dateCheck whether your robot needs 2.4GHz, move the router or dock closer, update the app
Error code you don't recogniseVaries by brand and modelLook the code up in the app or the brand's support page before you open anything

General guidance only. Always follow the manual for your model, switch the robot off before you clean brushes or sensors, and don't open sealed parts while it's under warranty.

Start here: the five-minute reset

  1. Switch the robot off and unplug the dock for a minute, then power both back on.
  2. Empty the bin and, if your dock has one, check the dust bag isn't full.
  3. Pull out the main brush and side brush and clear any hair or thread.
  4. Wipe the charging contacts, cliff sensors and the LiDAR or camera window with a dry microfibre cloth.
  5. Update the app and the robot's firmware, then try a short clean of one room.

If that fixes it, set a reminder for regular care. Our how to clean a robot vacuum guide has a step-by-step routine for brushes, filters, sensors and the dock.

Charging and docking problems

A robot that won't charge usually has dirty contacts or can't line up with the dock. Wipe the metal contacts on both, make sure the dock sits flat against a wall on a hard surface, and keep the area in front of it clear. Many brands ask for clear space either side of the dock; the exact distance is in your manual. If the robot still won't charge, the battery may be worn. Batteries are consumable, and how long they last depends on use. See how long robot vacuums last.

Getting stuck and missing rooms

Cords, rug tassels, socks and low furniture are the usual traps. Use no-go zones or virtual walls in the app rather than moving furniture every time. If your robot can't cross a door track or threshold, compare the height with the threshold figure on the brand's listing. Listed figures vary widely by model; some flagships, such as the MOVA MOBIUS 60, list up to 8 cm. If the map looks wrong after you move furniture, clean the navigation sensor window and re-map. Camera-based robots can also struggle in very dark rooms; our LiDAR vs camera navigation guide explains why.

Suction, brushes and smells

Weak pickup is almost always a full bin, a blocked filter or a wrapped brush. Filters and brushes wear out, so budget for replacements: our robot vacuum running costs guide covers what parts cost. If you have pets, an anti-tangle brush helps; see anti-tangle robot vacuums. A smelly robot usually means a damp mop or dirty-water tank left sitting. Empty and rinse the tank after mopping and let pads dry fully.

When it's a warranty job

Stop troubleshooting and contact the seller or brand if the robot won't power on, the battery swells or gets hot, a motor makes grinding noises, or the same error returns after a reset and clean. Opening the robot yourself can affect the brand warranty. Under the Australian Consumer Law, products must be of acceptable quality, and that guarantee sits on top of whatever warranty the brand offers. Our robot vacuum warranty guide lists brand terms and how to claim.

Related guides

Robot vacuums hub · How to clean a robot vacuum · Robot vacuum warranty in Australia · Running costs · How long robot vacuums last

How we researched this

This guide pulls together common faults and fixes described in robot vacuum manuals and brand support pages, plus our existing research on maintenance, warranty and running costs. It's general advice, not a repair manual: steps differ by brand and model, so check your own manual first. We haven't diagnosed or repaired these robots ourselves. See how we research.

Common questions

Why won't my robot vacuum charge?

Usually dirty charging contacts, a dock that's been moved or blocked, or the dock's power point being off. Wipe the contacts, give the dock clear space and restart both. If it still won't charge, the battery may be worn and it may be a warranty matter.

Why does my robot vacuum keep getting stuck?

Cords, rug tassels, low furniture and high door thresholds are the usual causes. Set no-go zones in the app and check your robot's listed threshold height.

Why has my robot vacuum lost suction?

A full bin or dock bag, a clogged filter or hair wrapped around the brush. Clean or replace those parts first.

Should I reset my robot vacuum to factory settings?

Only after simpler fixes fail. A factory reset can delete your saved maps and schedules, so check the brand's instructions first.

Is a robot vacuum fault covered by the Australian Consumer Law?

If a product isn't of acceptable quality, you may be entitled to a repair, replacement or refund under the Australian Consumer Law, on top of the brand warranty. Contact the retailer first.

Has Domestic Robot tested these fixes?

No. This is a researched guide based on manuals and brand support information.

Get new reviews and price drops

One email when new reviews and price drops land. No spam, unsubscribe any time.